DVgo device emulator

Node.js ThingsBoard device emulator with a SQLite-backed web portal. Each virtual device can connect over MQTT, publish live *_s telemetry, react to shared-attribute commands from the apps, and be taken offline without deleting the ThingsBoard record.

Requires Node 22+ (uses the built-in node:sqlite module).

Python historical data generation is not included.

What it does

Create / delete real ThingsBoard devices via the REST API (delete still removes the emulator row if the TB device is already gone)
Persist credentials, telemetry, published-key selection, and plant settings in SQLite
MQTT connect with the device access token as username (v1/devices/me/telemetry, plus attributes and RPC)
Web portal (http://localhost:3080) to:
- add devices (or attach an existing MQTT access token)
- select devices (select all / deselect all) and enable, disable, or delete
- Connect / Disconnect MQTT (new devices stay idle until you connect)
- start / stop the telemetry loop (Start telemetry is disabled until connected)
- toggle which keys are included in each publish (per-card On, plus select all / deselect all under Publish now)
- edit every live _s key from the device dashboard
- run a virtual plant that follows boost and schedule commands from the apps

On startup, devices already in SQLite are restored. They reconnect only if they were left enabled (not disabled). New devices are created disconnected, with telemetry off.

Virtual plant

While MQTT is connected, the device polls ThingsBoard shared attributes every 5 seconds (and also receives live pushes). It understands:

Source	Keys
One-shot boost	`boostNowHw`, `boostNowAux` (minutes; written by the apps via TB REST)
HW schedule	`hwRlyMode` 2 or 3, plus `hwRlySchedMode0/1StartTime` / `StopTime` (minutes since midnight)
Aux schedule	`auxRlyMode` 2 or 3, plus `auxRlySchedMode0/1Start` / `Stop`

Schedule saves in the apps are SQL-only, so this emulator polls rather than waiting for a TB push.

Behaviour:

Red / grey lamps for hot water boost and aux boost / divert
While HW is on, heatsink_s rises at Heat rate (°C / min) (integer, default 1)
At Thermostat max (°C) (default 65) heating stops, rlyInSel_s goes to 0, and boostNowHw is written back to ThingsBoard as 0
Live state is published as heatsink_s, rlyInSel_s, auxOn_s, auxRelay_s

Telemetry keys

Each device can publish the following live *_s keys on v1/devices/me/telemetry. Dashboard cards are ordered Status, Power, Energy flows, Energy today, Validity. Only keys with On checked are sent.

Status

heatsink_s — hot water / tank temperature (°C)
batterySoc_s — battery state of charge (%)
soc_s — SoC fallback (%)
batteryPercent_s — battery percent fallback (%)
auxOn_s — aux on (0/1)
auxRelay_s — aux relay (0/1)
rlyInSel_s — control load heating (0/1)
xCntlLoadState — control load state (integer; no _s suffix)

Power (W)

solarPower_s — solar generation
loadPower_s — home load
hotWaterInPower_s — hot water in
hotWaterOutPower_s — hot water out
batteryPower_s — battery power (negative = charging, positive = discharging)
gridPower_s — grid power (positive = importing, negative = exporting)

Energy flows (W)

solarToLoadPower_s
solarToHotWaterPower_s
solarToBatteryPower_s
solarToGridPower_s
gridToLoadPower_s
gridToHotWaterPower_s
gridToBatteryPower_s
batteryToLoadPower_s
batteryToHotWaterPower_s
batteryToGridPower_s

Energy today (Wh)

solarToday_s
loadToday_s
hotWaterInToday_s
hotWaterOutToday_s
solarToLoadToday_s
solarToHotWaterToday_s
solarToGridToday_s
solarToBatteryToday_s
gridToLoadToday_s
gridToHotWaterToday_s
gridToBatteryToday_s
batteryToLoadToday_s
batteryToHotwaterToday_s — note the lowercase w in Hotwater
batteryToGridToday_s
batteryExportToday_s
batteryImportToday_s
gridImport_s
gridExport_s

Validity

vPwrReadings_s — bitmask of valid live power keys (65535 = bits 0–15 all valid)

Setup

cp .env.example .env
# fill TB_USERNAME / TB_PASSWORD (tenant admin or a user who can create devices)
npm install
npm start

Open http://localhost:3080.

Optional env:

PORT — portal port (default 3080)
TB_HTTP_URL — ThingsBoard REST origin (default https://tb-dvgo.datavolt.au)
TB_DEVICE_PROFILE_ID — defaults to the Diverter / DVgo profile (e6b53240-7fec-11f1-a69d-edbc0b9170ac). The add-device dropdown is preselected to a profile named Diverter or DVgo when ThingsBoard returns one.
TB_DEVICE_TYPE — default DVgo
TB_MQTT_URL — default mqtts://tb-dvgo.datavolt.au:8883 (TLS). Port 1883 is not reachable from outside the TB host.
TB_MQTT_INSECURE — true to skip TLS certificate verification
PORTAL_USER / PORTAL_PASSWORD — basic auth for the control API
ALLOWED_IPS — comma-separated allowlist for /api
TELEMETRY_INTERVAL_MS — default 5000
DB_PATH — default ./data/emulator.db

If a device already exists in ThingsBoard, paste its MQTT access token in the add form and skip REST provisioning. If create times out, the portal can look the device up by name and adopt it.

5.3 KiB Raw Blame History Unescape Escape